点击图片查看原图
物添加剂组成，粉料与添加剂混合后，发生化学反应，形成一层坚韧的弹性防水膜，该膜对混凝土和灰浆有良好的粘附性，
能与之形成紧密牢固的永久性结合，阻止了水的渗透。
Introduction
Flexible water-proof paint is bi-component cement based water-proof material composed of superior bone materials, auxiliary agent and liquid high polymer additive, the powder and additive are blended and happen chemical reaction and shaped into water-proof elastic rubber film that has good viscosity to concrete and mortar to prevent water penetration.
产品特点
1、 富有柔韧性、粘结力佳.
2、能在潮湿环境下施工。
3、具有良好的透气性能，优异的耐老化性能和良好的耐腐蚀性。
4、无毒无害，属新一代环保产品。
Features
1. Good flexibility and viscosity;
2. Construct under damp environment;
3. Good permeability, good ageing resistance and corrosion resistance;
4. No toxicity, no nocuity it’s a new eco-friendly product.
适用范围
1、各种管道周围、伸缩缝、结构裂缝、水泥纤维板、金属板的连接处等。
2、建筑物屋顶、阳台、地下室、卫生间、水槽、游泳池、地铁、隧道等防水工程。
Applications
1. Various pipes, expansion points, structural cracks, cement fiber board and metal board;
2. Rooftop, balcony, basement, bathroom, water tank, swimming pool, metro and tunnel.
基面处理
1、表面必须平整、坚实、干净、无油污、无灰尘以及其他松动物。
2、明显的空隙和砂眼须用水泥砂浆堵塞、抹平、尖锐的边缘应除去。
3、预先润湿底材至无积水为准。
4、新浇注的混凝土应有一定的干固养护时间，防止混凝土干缩造成影响。
5、旧的混凝土面必须先用清水冲洗干净，晾干后涂刷。
Surface finishing
1. Keep the surface plane, solid, clean without oil dirt, dust or other loose matters;
2. Obvious gap and hole should be filled by cement mortar and sharp edges must be eliminated;
3. Wet the base material till no seeable water;
4. Newly-cast concrete should take some time to dry and maintain to avoid concrete shrinking;
5. Old concrete surface must be cleaned by water and then coated.
施工工艺
1、将粉剂慢慢倒入液剂并不断搅拌，直到搅拌成均匀糊状且无小粒子和气泡，即可使用。
2、用毛刷或滚刷直接涂刷胶浆于基面上，不可漏刷，为防止沉淀，操作过程中应保持间断性搅拌。
4、一般涂刷二遍以上（各涂层的方向应该交错），最后的涂膜厚度保持在1.0-1.2mm，用量为1-2kg/m2。
5、在涂刷的同时，在拐角接缝和裂纹处用无纺布或玻璃纤维加强，以增强抗裂抗拉性能，防水膜直接粘贴瓷砖时，必须涂饰
表面使防水膜完全覆盖基材，以达到防水作用。
Technical Process
1. Pour the powder agent into the liquid and keep stirring till no granules or bubbles could be seen;
2. Use brush or rolling brush to coat the paint on the base surface, keep stirring in a interval to avoid depositing;
3. Two times of brushing is needed (two directions), the final coating film should have 1.0-1.2mm depth, 1-2kg/m2;
4. It’s advised to use non-woven fabric or fiberglass to strengthen the viscosity at the joint and crack to enhance the extension; if the film is stuck on the ceramic tile directly, it must coat the surface to make the film fully cover the base material.
注意事项
1、 施工中应确保本品完全覆盖基面，养护24小时后方可进行其他作业。
2、在对耐磨性要求较高的场合如人行通道，需加硬化层以保护膜层不受破坏.
3、要求在5~40℃的温度环境下施工。
4、切忌将已干结的胶浆加水混合后再用。
Cautions
1. Ensure the base material is fully covered and other works could be conducted in 24 hours;
2. For those areas where have higher requirements to the abrasion performance, it needs to add hardening layer to protect the film;
3. Construction temperature:5~40℃
4. Do NOT add water into the dried mortar for second use.
包装储存
置于阴凉干燥处，未开封的本品可贮存12个月。
Package and Storage
Store in cool and dry places, storage period: 12 months.
